Toyota Lexus IS300 Manual Download Page 161 | Manualshive

Page: 161 / 389

background image

COMFORT ADJUSTMENT

148

SV16055

Move seat fully back

A forward–facing child restraint system should be
allowed to be put on the front passenger seat only
when it is unavoidable. Always move the seat as far
back as possible, because the force of the deploying
front passenger airbag could cause death or serious
injury to the child.

On vehicles with side airbags and curtain shield
airbags, do not allow the child to lean over the front
door or around the front door even if the child is
seated in a child restraint system. It is dangerous if
the side and curtain shield airbags inflate, and the
impact could cause death or serious injury to the
child.

SV16075

Do not put a child restraint system on the rear seat if
it interferes with the lock mechanism of the front
seats. This may cause death or serious injury to the
child and front passenger in case of sudden braking
or a collision.

If the driver’s seat position does not allow sufficient
space for safe installation, install the child restraint
system on the rear right seat.

2003 IS300 from Aug. ’02 Prod. (OM53439U)

«
...
159
160
161
162
163
...
»

Summary of Contents for Lexus IS300






































































































































































































































































































































































































Reviews:

No comments

Related manuals for Lexus IS300

Brand: Acdeos Pages: 38

Green Motion Building

Brand: Eaton Pages: 12

Brand: TATA Motors Pages: 156

Brand: Mazda Pages: 122

Brand: Hank Pages: 2

JEEP GL ADIATOR JT TOPPER ROOF RACK

Brand: JCROffroad Pages: 7

IVH-9000-2R440Q

Brand: Vecow Pages: 110

Sprinter Side Ladder

Brand: FVC Pages: 8

PRIME DESIGN HRR-369-E-UM3-96

Brand: Safe Fleet Pages: 12

Brand: Kocchi's Pages: 4

Brand: Skoda Pages: 2

Brand: Jaeger Pages: 13

Brand: Mitsubishi Pages: 284

Giulia 952 2017

Brand: Alfa Romeo Pages: 324

Brand: Rhino-Rack Pages: 4

Brand: Hella Gutmann Pages: 380

Brand: Toyota Pages: 5

Brand: Toyota Pages: 9

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands