Toyota Lexus IS300 Manual Download Page 363

Page: 363 / 389

ELECTRICAL COMPONENTS

350

Checking battery condition

Checking by indicator

SV64016

Check the battery condition by the indicator color.

BLUE – Good condition.

WHITE – Charging necessary. Have the battery checked
by your Lexus dealer.

RED – Have the battery checked by your Lexus dealer.

NOTICE

Do not refill the battery with water.

BATTERY RECHARGING

PRECAUTIONS

During recharging, the battery is producing hydrogen
gas.

Therefore, before recharging:

1. If recharging with the battery installed on the vehicle, be
sure to disconnect the ground cable.

2. Make sure the power switch on the recharger is off when
connecting the charger cables to the battery and when
disconnecting them.

CAUTION

Always charge the battery in an unconfined area. Do
not charge the battery in a garage or closed room
where there is not sufficient ventilation.

Only do a slow charge (5 A or less). Charging at a
quicker rate is dangerous. The battery may explode
causing personal injuries.

NOTICE

Never recharge the battery while the engine is running.
Also, be sure all accessories are turned off.

2003 IS300 from Aug. ’02 Prod. (OM53439U)

Summary of Contents for Lexus IS300






































































































































































































































































































































































































Search results

Summary of Contents for Lexus IS300

Reviews:

Related manuals for Lexus IS300

Brands by name

Popular brands

Toyota Lexus IS300, Manual

Search results

Summary of Contents for Lexus IS300

Reviews:

Related manuals for Lexus IS300

Brands by name

Popular brands