Toyota Lexus IS300 Manual Download Page 301 | Manualshive

Page: 301 / 389

background image

IN CASE OF AN EMERGENCY

288

(d) Emergency towing

SV41032

If towing is necessary, we recommend you to have it done
by your Lexus dealer or a commercial tow truck service.

If towing service is not available in an emergency, your
vehicle may be temporarily towed by a cable or chain
secured to the emergency towing eyelet. Use extreme
caution when towing the vehicle.

NOTICE

Only use specified towing eyelet; otherwise your
vehicle may be damaged.

A driver must be in the vehicle to steer it and operate the
brakes.

Towing in this manner may be done only on hard–surfaced
roads for a short distance and at low speeds. Also, the wheels,
axles, drive train, steering and brakes must all be in good
condition.

CAUTION

Use extreme caution when towing the vehicle. Avoid
sudden starts or erratic driving maneuvers which would
place excessive stress on the emergency towing eyelet
and towing cable or chain. The eyelet and towing cable
or chain may break and cause serious injury or damage.

NOTICE

Use only a cable or chain specifically intended for use
in towing vehicles. Securely fasten the cable or chain
to the towing eyelet provided.

Before towing, release the parking brake and put the
transmission in neutral (manual) or ”N” (automatic). The
ignition key must be in ”ACC” (engine off) or ”ON” (engine
running).

CAUTION

If the engine is not running, the power assist for the
brakes and steering will not work so steering and
braking will be much harder than usual.

2003 IS300 from Aug. ’02 Prod. (OM53439U)

«
...
299
300
301
302
303
...
»

Summary of Contents for Lexus IS300






































































































































































































































































































































































































Reviews:

No comments

Related manuals for Lexus IS300

Brand: KC HiLiTES Pages: 4

Brand: Lancia Pages: 386

FRONT HEADLIGHT LENS COVER

Brand: Bimmer Jakes Pages: 4

Brand: JANE Pages: 21

Brand: Honda Pages: 32

Brand: Honda Pages: 20

2009 Rio Series

Brand: Kia Pages: 219

Brand: Velleman Pages: 12

Brand: Belkin Pages: 2

Brand: KEKO Pages: 13

Stealth 4191F Series

Brand: Road Armor Pages: 5

Brand: rough country Pages: 4

Brand: Prorack Pages: 14

Brand: Hama Pages: 13

Pro Competition

Brand: G-Tech Pages: 180

MagicWatch MWE850

Brand: Waeco Pages: 200

Brand: Air Lift Pages: 12

CommCenter 300MB-SD

Brand: Federal Signal Corporation Pages: 60

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands