Toyota Lexus IS300 Manual Download Page 285 | Manualshive

Page: 285 / 389

background image

IN CASE OF AN EMERGENCY

272

IF YOU HAVE A FLAT TIRE

1. Reduce your speed gradually, keeping a straight line.
Move cautiously off the road to a safe place – well away from
the traffic. Avoid stopping on the center divider of a highway.
Park on a level spot with firm ground.

2. Stop the engine and turn on your emergency flashers.

3. Firmly set the parking brake and put the transmission in ”P”
(automatic) or reverse (manual).

4. Have everyone get out of the vehicle on the side away from
traffic.

5. Read the following instructions thoroughly.

CAUTION

When jacking, be sure to observe the following to
reduce the possibility of personal injury:

Follow jacking instructions.

Do not put any part of your body under a vehicle
supported by a jack. Personal injury may occur.

Do not start or run the engine while your vehicle is
supported by the jack.

Stop the vehicle on a level firm ground, firmly set the
parking brake and put the transmission in ”P”
(automatic) or reverse (manual). Block the wheel
diagonally opposite to the one being changed if
necessary.

Make sure to set the jack properly in the jack point.
Raising the vehicle with jack improperly positioned
will damage the vehicle or may allow the vehicle to fall
off the jack and cause personal injury.

Never get under the vehicle when the vehicle is
supported by the jack alone.

Use the jack only for lifting your vehicle during wheel
changing.

Do not raise the vehicle with someone in the vehicle.

When raising the vehicle, do not put an object on or
under the jack.

Raise the vehicle only high enough to remove and
change the tire.

NOTICE

Do not continue driving with a deflated tire. Driving
even a short distance can damage a tire and wheel
beyond repair.

2003 IS300 from Aug. ’02 Prod. (OM53439U)

«
...
283
284
285
286
287
...
»

Summary of Contents for Lexus IS300






































































































































































































































































































































































































Reviews:

No comments

Related manuals for Lexus IS300

Brand: Baja Designs Pages: 6

Brand: Mazda Pages: 527

2008 Escalade EXT

Brand: Cadillac Pages: 496

DAF POWERCHOICE 250A

Brand: Paccar Pages: 20

Brand: DEFA Pages: 7

Brand: Prorack Pages: 15

Brand: Mazda Pages: 720

Brand: iArmor Pages: 4

autoSteady AS101

Brand: Enduro Pages: 48

Parrot MKi + ParrotCK3100 range LOGAN

Brand: Parrot Pages: 10

Brand: Simplicity Pages: 10

Dunlop L.D02.C.M

Brand: Sumitomo Pages: 22

Brand: Brodit Pages: 2

Brand: Belkin Pages: 30

Brand: Mitsubishi Pages: 141

Brand: Kia Pages: 673

Brand: Rhino-Rack Pages: 5

Brand: Gator Pages: 18

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands