manualshive.com logo in svg

Toyota Lexus IS300, Manual

The Toyota Lexus IS300 manual is a must-have for owners and enthusiasts alike. This comprehensive user manual provides detailed instructions and information about the luxurious IS300 model, allowing you to fully delve into its features and functionalities. Download your free manual from manualshive.com to unlock the full potential of your IS300 experience.

Share
Download
background image

INTERIOR EQUIPMENT

61

Cigarette Lighter

To use the cigarette lighter, press it in.  After it finishes
heating up, it automatically pops out ready for use.

Do not hold the cigarette lighter pressed in.

If the engine is not running, the ignition key must be in the
”ACC” position to use the lighter.

Use a Lexus genuine cigarette lighter or equivalent for
replacement.

Ashtray

To use the ashtray, open the cover.

When finished with your cigarette, thoroughly extinguish it in
the ashtray to prevent other cigarette butts from catching fire.
After using the ashtray, close the ashtray cover completely.

To remove the ashtray, open the ashtray cover and pull it out.

CAUTION

To reduce the chance of injury in case of an accident or
sudden stop while driving, always completely close the
ashtray after use.

POWER OUTLET

SV14029a

In the console box

SV14010

In the luggage compartment (SportCross only)

2003 IS300 from Aug. ’02 Prod. (OM53439U)

Summary of Contents for Lexus IS300






































































































































































































































































































































































































Reviews:

No comments

Related manuals for Lexus IS300

PEUGEOT Partner Origin Handbook preview
Partner Origin
Brand: PEUGEOT Pages: 128
Schumacher Electric SPI6 Owner'S Manual preview
SPI6
Brand: Schumacher Electric Pages: 87
Cadillac 2009 ESCALADE ESV Owner'S Manual preview
2009 ESCALADE ESV
Brand: Cadillac Pages: 602
BendPak Autostacker PL-6SR Installation And Operation Manual preview
Autostacker PL-6SR
Brand: BendPak Pages: 104
RBP STEALTH POWER RBP-216-SP Installation Manual preview
STEALTH POWER RBP-216-SP
Brand: RBP Pages: 16
HURST STREET SUPER SHIFTER Installation Instructions preview
STREET SUPER SHIFTER
Brand: HURST Pages: 2
VDO VIEWLINE 52 MM - MOUNTING 11-09 Installation Instructions preview
VIEWLINE 52 MM - MOUNTING 11-09
Brand: VDO Pages: 4
Mercedes-Benz 2016 SLK Operator'S Manual preview
2016 SLK
Brand: Mercedes-Benz Pages: 358
Park-Daddy PD50AA Installation Manual preview
PD50AA
Brand: Park-Daddy Pages: 22
Toyota CAMRY HV Manual preview
CAMRY HV
Brand: Toyota Pages: 636
Nav TV Ford 4” UNI-CAM Manual preview
Ford 4” UNI-CAM
Brand: Nav TV Pages: 6
Saab 2007 9-3 Remote Starter Owner'S Manual preview
2007 9-3 Remote Starter
Brand: Saab Pages: 304
Valeo Park Vision VAL632210 Instruction Manual preview
Park Vision VAL632210
Brand: Valeo Pages: 25
Unex OBU-352EC Quick Start Manual preview
OBU-352EC
Brand: Unex Pages: 30
SilverLeaf Electronics VMS 645 CL Owner'S Manual preview
VMS 645 CL
Brand: SilverLeaf Electronics Pages: 16
Caraudio-Systems RL-LR12-TF Manual preview
RL-LR12-TF
Brand: Caraudio-Systems Pages: 9
Yakima Landing Pad 11 Manual preview
Landing Pad 11
Brand: Yakima Pages: 28
CARFACE CF145962E Instruction Manual preview
CF145962E
Brand: CARFACE Pages: 16

Brands by name

Popular brands

Load more brands