manualshive.com logo in svg

Toyota Lexus IS300, Manual

The Toyota Lexus IS300 manual is a must-have for owners and enthusiasts alike. This comprehensive user manual provides detailed instructions and information about the luxurious IS300 model, allowing you to fully delve into its features and functionalities. Download your free manual from manualshive.com to unlock the full potential of your IS300 experience.

Share
Download
background image

INTRODUCTION

305

POSITIONING THE JACK

SV61006

Front of vehicle

When jacking up your vehicle with the jack, position the
jack correctly as shown in the illustration.

Jack position . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Front– Front crossmember 
Rear– Rear differential

Support position and Pantograph jack position . . . . . 

CAUTION

When jacking, be sure to observe the following to
reduce the possibility of personal injury:

Follow jacking instructions.

Do not put any part of your body under the vehicle
supported by a jack.  Personal injury may occur.

Do not start or run the engine while your vehicle is
supported by the jack.

Stop the vehicle on a level firm ground, firmly set the
parking brake and put the transmission in ”P”
(automatic) or reverse (manual). Block the wheel
diagonally opposite to the one being changed if
necessary.

Make sure to set the jack properly in the jack point.
Raising the vehicle with jack improperly positioned
will damage the vehicle or may allow the vehicle to fall
off the jack and cause personal injury.

Never get under the vehicle when the vehicle is
supported by the jack alone; use vehicle support
stands.

Do not raise the vehicle with someone in the vehicle.

When raising the vehicle, do not place any objects on
top of or underneath the jack.

2003 IS300 from Aug. ’02 Prod. (OM53439U)

Summary of Contents for Lexus IS300






































































































































































































































































































































































































Reviews:

No comments

Related manuals for Lexus IS300

Jabra SP200 - QUICKSTART GUIDE 1 Quick Start Manual preview
SP200 - QUICKSTART GUIDE 1
Brand: Jabra Pages: 2
Jabra BT150 - Headset - Over-the-ear Quick Start Manual preview
BT150 - Headset - Over-the-ear
Brand: Jabra Pages: 2
Kargo Master 40131 Installation Manual preview
40131
Brand: Kargo Master Pages: 5
iDataLink maestro Pr 2 Install Manual preview
maestro Pr 2
Brand: iDataLink Pages: 99
Club Car Gasoline/Electric DS Golf Car 1996 Owner'S Manual preview
Gasoline/Electric DS Golf Car 1996
Brand: Club Car Pages: 48
Firestone Ride-Rite Air Helper Springs 2173 Installation Instructions preview
Ride-Rite Air Helper Springs 2173
Brand: Firestone Pages: 4
Meta System 900000358 Installation Technical Sheet preview
900000358
Brand: Meta System Pages: 22
Needit Park Mini User Manual preview
Park Mini
Brand: Needit Pages: 2
Gemini KIT ParkingSensor 814 Installation And Use Manual preview
KIT ParkingSensor 814
Brand: Gemini Pages: 6
GROM Audio VLINE Installation Manual preview
VLINE
Brand: GROM Audio Pages: 20
Reimo TOUR EASY 4 936550 Quick Start Manual preview
TOUR EASY 4 936550
Brand: Reimo Pages: 4
Kolpin 1466 Product Instructions preview
1466
Brand: Kolpin Pages: 6
PEUGEOT 5008 2017 Handbook preview
5008 2017
Brand: PEUGEOT Pages: 404
Chrysler Sebring Convertible Owner'S Manual preview
Sebring Convertible
Brand: Chrysler Pages: 454
Lincoln 2012 MKX Owner'S Manual preview
2012 MKX
Brand: Lincoln Pages: 364
Alfa Romeo Stelvio 2019 User Manual preview
Stelvio 2019
Brand: Alfa Romeo Pages: 268
Panavise Indash 75114-296 Installation Instructions preview
Indash 75114-296
Brand: Panavise Pages: 2
LetsGoAero V2 Two-Bike Carrier User Manual preview
V2 Two-Bike Carrier
Brand: LetsGoAero Pages: 2

Brands by name

Popular brands

Load more brands