Toyota Lexus IS300 Manual Download Page 292 | Manualshive

Page: 292 / 389

background image

IN CASE OF AN EMERGENCY

279

SV04003

4. Position the jack at the jack points as shown.

Make sure the jack is positioned on a level and solid surface.

SV41031

5. After making sure no one is in the vehicle, raise it high
enough so that the spare tire can be installed.

Allow for the fact that you need more ground clearance when
putting on the spare tire than when removing the flat tire.

To raise the vehicle, insert the jack handle into the jack (it is a
loose fit) and turn it clockwise. As the jack touches the vehicle
and begins to lift, double–check that it is properly positioned.

CAUTION

Never get under the vehicle when the vehicle is
supported by the jack alone.

2003 IS300 from Aug. ’02 Prod. (OM53439U)

«
...
290
291
292
293
294
...
»

Summary of Contents for Lexus IS300






































































































































































































































































































































































































Reviews:

No comments

Related manuals for Lexus IS300

Brand: VanEssa mobilcamping Pages: 8

Brand: Jeep Pages: 25

Brand: Laser Pages: 8

Brand: Whispbar Pages: 15

2007 MazdaSpeed6

Brand: Mazda Pages: 12

Brand: WABCO Pages: 48

Quattroporte Automatic

Brand: Maserati Pages: 272

Brand: Volvo Pages: 24

Brand: Prorack Pages: 20

Brand: ULTIMATE SPEED Pages: 50

Brand: Cadillac Pages: 529

Brand: Toro Pages: 16

Brand: Mitsubishi Pages: 362

Brand: Honda Pages: 253

Brand: Toyota Pages: 11

Brand: Maserati Pages: 37

T13 Outback Frontal Protection System

Brand: T.J.M. Pages: 18

Brand: Audi Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands