Toyota Lexus IS300 Manual Download Page 191 | Manualshive

Page: 191 / 389

background image

THEFT DETERRENT

178

THEFT PREVENTION LABELS

17L002

Your new vehicle carries theft prevention labels which are
approximately 56 mm (2.20 in.) by 16 mm (0.63 in.).

The purpose of these labels is to reduce the incidence of
vehicle thefts by facilitating the tracing and recovery of parts
from stolen vehicles. The label is designed so that once it is
applied to a surface, any attempt to remove it will result in
destroying the integrity of the label. Transferring these labels
intact from one part to another will be impossible.

NOTICE

You should not attempt to remove the theft prevention
labels as it may violate certain state or federal laws.

2003 IS300 from Aug. ’02 Prod. (OM53439U)

«
...
189
190
191
192
193
...
»

Summary of Contents for Lexus IS300






































































































































































































































































































































































































Reviews:

No comments

Related manuals for Lexus IS300

Brand: Warrior Winches Pages: 17

Brand: Ford Pages: 52

Brand: Kuda-Phonebase Pages: 3

Brand: Whispbar Pages: 14

Brand: TAUBENREUTHER Pages: 8

Brand: Jeep Pages: 136

Brand: Metra Electronics Pages: 2

Brand: Toyota Pages: 636

Brand: NavInc Pages: 6

Denali 1094-0185-15

Brand: E&G Classics Pages: 3

Brand: Metra Electronics Pages: 2

Brand: Mobridge Pages: 20

Brand: Arrista Pages: 2

Brand: TATA Motors Pages: 232

Brand: Maserati Pages: 37

1953 Traction Avant

Brand: CITROEN Pages: 26

Brand: Painless Performance Pages: 16

Brand: EUFAB Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands