Toyota Lexus IS300 Manual Download Page 368

Page: 368 / 389

ELECTRICAL COMPONENTS

355

CHECKING THE HEADLIGHT AIM

SV64027

Vertical movement adjusting bolt 1

Vertical movement adjusting bolt 2

Before checking the headlight aim:

1. Be sure that the body around the headlight is not deformed.

2. Park the vehicle on a level spot.

3. The driver gets into the driver’s seat and puts the vehicle in
a state readying for a driving (with a full tank).

4. Bounce the vehicle several times.

Adjusting the vertical aiming

SV64051

1. Turn the vertical movement adjusting bolt 1 in either
direction. At this time, keep the turning direction and number
of turns in mind.

2003 IS300 from Aug. ’02 Prod. (OM53439U)

Summary of Contents for Lexus IS300






































































































































































































































































































































































































Search results

Summary of Contents for Lexus IS300

Reviews:

Related manuals for Lexus IS300

Brands by name

Popular brands

Toyota Lexus IS300, Manual

Search results

Summary of Contents for Lexus IS300

Reviews:

Related manuals for Lexus IS300

Brands by name

Popular brands