Toyota Lexus IS300 Manual Download Page 46

Page: 46 / 389

SWITCHES

REAR WINDOW WIPER AND

WASHER SWITCH

SV12018

Washer on during wiping 2 Washer on

To turn the wipers on, twist the knob at the end of the lever.

The ignition key must be in the ”ON” position.

There are 2 settings:

”INT” position:

Intermittent operation

”ON” position: Low speed operation

To make the washer squirt, twist the knob downward to
position 2.

To make the washer squirt while operating in ”ON”
position, twist the knob upward to position 1.

The knob automatically returns from these positions after you
release it.

For information on adding washer fluid, see ”Adding washer
fluid” on page 354.

NOTICE

Do not operate the rear window wiper if the rear window
is dry. It may scratch the glass.

2003 IS300 from Aug. ’02 Prod. (OM53439U)

Summary of Contents for Lexus IS300






































































































































































































































































































































































































Search results

Summary of Contents for Lexus IS300

Reviews:

Related manuals for Lexus IS300

Brands by name

Popular brands

Toyota Lexus IS300, Manual

Search results

Summary of Contents for Lexus IS300

Reviews:

Related manuals for Lexus IS300

Brands by name

Popular brands