Toyota Lexus IS300 Manual Download Page 351 | Manualshive

Page: 351 / 389

background image

CHASSIS

338

INSTALLING SNOW TIRES AND

CHAINS

When to use snow tires or chains

Snow tires or chains are recommended when driving on
snow or ice.

On wet or dry roads, conventional or radial tires provide better
traction than snow or studded tires.

Snow tire selection

If you need snow tires, select tires of the same size,
construction and load capacity as the originally installed
tires.

Do not use tires other than stated above. Since your vehicle
has radial tires as original equipment, make sure your snow
tires also have radial construction. Do not install studded tires
without first checking local regulations for possible restrictions.

CAUTION

Observe the following instructions. Otherwise, an
accident may occur resulting in death or serious
injuries.

Do not use snow tires other than the manufacturer’s
recommended size, as this may cause dangerous
handling characteristics resulting in loss of control.

Snow tire installation

Snow tires should be installed on all wheels.

Installing snow tires on the rear wheels only can lead to an
excessive difference in road grip capability between the front
and rear tires which could cause loss of vehicle control.

CAUTION

Do not drive with the snow tires incorrectly inflated.

Never drive over 120 km/h (75 mph) with any type of
snow tires.

2003 IS300 from Aug. ’02 Prod. (OM53439U)

«
...
349
350
351
352
353
...
»

Summary of Contents for Lexus IS300






































































































































































































































































































































































































Reviews:

No comments

Related manuals for Lexus IS300

Brand: JANE Pages: 6

Brand: AA Products Pages: 8

Brand: Triumph Pages: 86

Brand: AccuAir Pages: 40

Brand: Peak Pages: 10

Brand: Toyota Pages: 56

Brand: Fiat Pages: 172

Brand: Honda Pages: 6

Brand: Pyle Pages: 4

Brand: EZTRUNK Pages: 3

Brand: Hummer Pages: 31

Brand: Honda Pages: 24

Perfect Fit MBM120

Brand: Waeco Pages: 3

Brand: Or-Fab Pages: 4

Brand: Jaeger Pages: 11

Brand: ATS Pages: 12

Brand: Connects2 Pages: 2

Brand: HUSKY LINERS Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands