manualshive.com logo in svg

Toyota Lexus IS300, Manual

The Toyota Lexus IS300 manual is a must-have for owners and enthusiasts alike. This comprehensive user manual provides detailed instructions and information about the luxurious IS300 model, allowing you to fully delve into its features and functionalities. Download your free manual from manualshive.com to unlock the full potential of your IS300 experience.

Share
Download
background image

INTERIOR EQUIPMENT

60

The displayed temperature ranges from –30

C (–22

F) up to

50

C (122

F).  The display flashes for 10 seconds when the

outside temperature goes down below 3

C (37

F) or less and

informs you that the outside temperature is low.  The warning
is repeated whenever the temperature rises to at least +5

C

(+41

F) and then sinks again to +3

C (37

F).  If the

temperature does not appear on the display or it shows ”– –”,
take your vehicle to your Lexus dealer.

CAUTION

The outside air temperature indicator is designed to
inform you when the air temperature is near freezing.
This indicator does not detect the presence of ice on the
road.  Drivers must exercise great caution in driving on
roads which are wet, slippery or icy.

CIGARETTE LIGHTER AND

ASHTRAY

SV14002

Cigarette lighter and front ashtray

SS14011

Rear ashtray

2003 IS300 from Aug. ’02 Prod. (OM53439U)

Summary of Contents for Lexus IS300






































































































































































































































































































































































































Reviews:

No comments

Related manuals for Lexus IS300

Compass 02106 Manual preview
02106
Brand: Compass Pages: 16
BMW E39/2 Installation Instructions Manual preview
E39/2
Brand: BMW Pages: 21
Volvo 1996 960 Quick Tips preview
1996 960
Brand: Volvo Pages: 10
ULTIMATE SPEED UAWSO 2 B1 Operation And Safety Notes preview
UAWSO 2 B1
Brand: ULTIMATE SPEED Pages: 32
Chevrolet 1998 Tahoe Manual preview
1998 Tahoe
Brand: Chevrolet Pages: 441
Havis C-DMM-3005 Installation Instructions preview
C-DMM-3005
Brand: Havis Pages: 5
TEINHOF V-295 Fitting And Operation Manual preview
V-295
Brand: TEINHOF Pages: 2
VDO FUEL TANK GAUGE Installation Instructions Manual preview
FUEL TANK GAUGE
Brand: VDO Pages: 10
Proxel EPS-DUAL Installation Instructions & User Manual preview
EPS-DUAL
Brand: Proxel Pages: 16
GMC Chevrolet CAMARO 1969 Owner'S Manual preview
Chevrolet CAMARO 1969
Brand: GMC Pages: 92
Prorack K671 Fitting Instructions Manual preview
K671
Brand: Prorack Pages: 17
Front Runner TBRA020 Quick Start Manual preview
TBRA020
Brand: Front Runner Pages: 7
Prorack K146 Fitting Instructions Manual preview
K146
Brand: Prorack Pages: 14
Honda 2012 insight Owner'S Manual preview
2012 insight
Brand: Honda Pages: 418
Metra Electronics Saddle Tramp BC-DSPX-HD2 Installation Instructions Manual preview
Saddle Tramp BC-DSPX-HD2
Brand: Metra Electronics Pages: 24
Toyota PT427-89060 Manual preview
PT427-89060
Brand: Toyota Pages: 5
Dodge STRATUS SEDAN 2006 Manual preview
STRATUS SEDAN 2006
Brand: Dodge Pages: 6
Dodge DURANGO 2019 User Manual preview
DURANGO 2019
Brand: Dodge Pages: 284

Brands by name

Popular brands

Load more brands