Toyota Lexus IS300 Manual Download Page 365 | Manualshive

Page: 365 / 389

background image

ELECTRICAL COMPONENTS

352

64L013

2. Make sure the inoperative component is turned off. Pull
the suspected fuse straight out with the pull–out tool and
check it. If it has blown, push a new fuse into the clips.

64G008

Good

Blown

a. Look carefully at the fuse. If the thin wire is broken, the fuse
has blown. If you are not sure or if it is too dark to see, try
replacing the suspected fuse with one of the same value that
you know is good.

b. Install only a fuse with the amperage rating designated on
the fuse box lid.

If you do not have a spare fuse, in an emergency you can pull
out the ”CIG”, ”RADIO NO.1” or ”OBD” fuse, which may be
dispensable for normal driving, and use it if its amperage rating
is the same.

If you cannot use one of the same amperage, use one lower
than, but as close as possible to, the amperage. If the
amperage is lower than that specified, the fuse might blow out
again but this does not indicate anything wrong. Be sure to get
the correct fuse as soon as possible and return the substitute
to its original clips.

2003 IS300 from Aug. ’02 Prod. (OM53439U)

«
...
363
364
365
366
367
...
»

Summary of Contents for Lexus IS300






































































































































































































































































































































































































Reviews:

No comments

Related manuals for Lexus IS300

Brand: GMC Pages: 20

Brand: PullRite Pages: 10

Road Ready Seat Protector

Brand: Wagan Pages: 12

Brand: Chevrolet Pages: 50

Brand: Uebler Pages: 56

Brand: ULTIMATE SPEED Pages: 50

Brand: Black Horse Off Road Pages: 7

Brand: ConWys AG Pages: 16

Brand: Poison Spyder Pages: 5

Brand: Buick Pages: 394

Brand: Laser Pages: 3

MagicWatch MWE150

Brand: Waeco Pages: 176

Brand: American muscle Pages: 3

Brand: Alu-Cab Pages: 6

Brand: GMC Pages: 40

Prime Design FBM-1027

Brand: Safe Fleet Pages: 8

Brand: dji Pages: 3

Brand: HOOKE ROAD Pages: 7

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands