Toshiba DP1600 Service Handbook Download Page 110

Page: 110 / 239

December 2000 © TOSHIBA TEC

2 - 7

1600/2000/2500 PREVENTIVE MAINTENANCE

*17. Pickup roller

To clean the surface of the pickup roller, use a cloth which should be soaked in water and then

wrung strongly.

*18. 2nd pinch roller

To clean the surface of the 2nd pinch roller, use a cloth which should be soaked in water and then

wrung strongly.

*19. 2nd feed roller

To clean the surface of the 2nd feed roller, use a cloth which should be soaked in water and then

wrung strongly.

*20. Paper guide/2nd paper guide

To clean the surface of the paper guides, use a cloth which should be soaked in water and then

wrung strongly.

*21. Separate roller

To clean the surface of the separate roller, use a cloth which should be soaked in water and then

wrung strongly.

*22. Feed roller

To clean the surface of the feed roller, use a cloth which should be soaked in water and then wrung

strongly.

*23. Photoconductive drum

Refer to "3.6 Checking and Cleaning of Photoconductive Drum (SRU type)".

*24. Drum cleaning blade

Since the edge of the blade is breakable and can be easily damaged by matters such as the adher-

ence of paper dust. Replace the cleaning blade with a new one if poor images are copied due to the

damaged blade regardless of the number of copies which have been made.

*25. Main charger case/main charger wire

Clean the main charger case and wire with a cloth soaked in water and then squeezed tightly.

Note: Be careful of the following when attaching a new wire (length: 358mm).

· Do not twist the wire.

· Do not touch the wire with your bare hand.

*26. Separation claws for the drum

The paper jam may be caused if the tip of the separation claw is damaged or deformed. If there is

any problem with it, replace the claw with a new one regardless of the number of copies which have

been made.

If any mark which was made by the claw appears on the copied image, clean the tip of the claw.

Notes: 1. Wipe the tip of the claw lightly with a dry cloth trying not to deform it.

Do not leave the lint on the tip.

2. Apply patting power to the tip of the claws and drum surface after replacing or cleaning

them to reduce the load on the drum surface by the claw.

01/11

Summary of Contents for DP1600















































































































































































































































Search results

Summary of Contents for DP1600

Reviews:

Related manuals for DP1600

Brands by name

Popular brands

Toshiba DP1600, Service Handbook

Search results

Summary of Contents for DP1600

Reviews:

Related manuals for DP1600

Brands by name

Popular brands