Toshiba DP1600 Service Handbook Download Page 133

Page: 133 / 239

December 2000 © TOSHIBA TEC

4 - 9

1600/2000/2500 TROUBLESHOOTING

E14

Tray 2 feeding jam

When recording paper is left on the recording paper path, remove it. If this error occurs fre-

quently, the following items should be checked.

Where was the paper stopped?

Near the registration roller

Is the 2nd feed roller sensor working? (using the test mode 04, Sensor Test, DATA No. 20

Bit 6)

1. Check if each connector between the 2nd feed roller sensor and the

PFC PWA (CN205) is disconnected.

2. Check if each connector between the PFC PWA (CN201) and the relay

PWA (CN36) is disconnected.

3. Check if each connector pin is removed or the harness is broken.

4. Check if any conductor pattern on the PFC, relay and main PWA is

open- or short-circuited.

5. Replace the 2nd feed roller sensor.

6. Replace the PFC PWA.

7. Replace the relay PWA.

8. Replace the main PWA.

Check to see if there are any foreign obstacles on the recording paper path.

Before reaching the 2nd feed roller

Is the 2nd feed roller clutch working? (using the test mode 10, Output Test, CODE 203)

YES

Summary of Contents for DP1600















































































































































































































































Search results

Summary of Contents for DP1600

Reviews:

Related manuals for DP1600

Brands by name

Popular brands

Toshiba DP1600, Service Handbook

Search results

Summary of Contents for DP1600

Reviews:

Related manuals for DP1600

Brands by name

Popular brands