manualshive.com logo in svg

Toshiba DP1600, Service Handbook

The Toshiba DP1600 Service Handbook is a comprehensive manual that provides detailed instructions for troubleshooting, repairing, and maintaining your Toshiba DP1600 product. Easily accessible as a free download from our website, this manual ensures you have the necessary information to maximize the performance of your device.

Share
Download
background image

1600/2000/2500  PRECAUTIONS FOR STORING & HANDLING SUPPLIES

3 - 4

December 2000 © TOSHIBA TEC

3.6

Checking and Cleaning of the Photoconductive Drum (SRU type)

(1) Use of gloves

Since fingerprints or oil stains on the drum surface affects the quality of the copy image and degrades

the characteristics of the photoconductor, do not touch the drum surface with your bare hands.

(2) Handling precautions

As the drum surface is very sensitive, be sure to handle the drum carefully when installing or removing

it so as not to damage its surface.

When the drum is replaced with a new one, apply patting powder (lubricant) on the entire surface of

the new drum (including both edges to where the OPC is not coated) and separation claw of the

cleaner before installing them. The drum counter must be cleared to 0 (zero) in the setting mode 08-

673.

Notes:

1. Application of the patting powder is to reduce friction among the drum, the cleaning blade and

the separation claw. If this process is not performed, the drum and the cleaning blade may be

damaged.

2. Remove any fibers or lint adhering to the blade since they can damage the drum and blade, or

allows defective cleaning.

(3) Installation of the copier and storage of the drum

Do not install the copier in a place where it may be exposed to high temperature, high humidity,

chemicals and/or chemical gas.

Do not leave the drum in a brightly lit place for a long time. Otherwise, it would be fatigued and causes

background fogging on the copied image right after it is installed in the machine. However, this phe-

nomenon will decrease as time elapses.

(4) Cleaning the drum

At the preventive maintenance, wipe the entire surface of the drum softly using the specified cleaning

cotton (dry soft pad). Use sufficiently thick cleaning cotton so as not to touch the drum surface directly

with your fingertips or nails. Remove your rings and wristwatch before cleaning so as not to damage

the drum.

Do not use organic solvents such as alcohol or silicone oil as they have a bad influence on the drum.

Do not use selenium refresher either.

(5) Scratches on the photoconductive drum surface

If the surface is scratched and the aluminum base is exposed, black spots or streaks will appear on

the copied images. Since those scratches can damage the cleaning blade, replace the drum with a

new one.

(6) Used photoconductive drums

Dispose of the used drums following the regulations regarding industrial waste established by your

local municipal office.

01/11

Summary of Contents for DP1600
















































































































































































































































Reviews:

No comments

Related manuals for DP1600

Canon NP-1215 Service Manual preview
NP-1215
Brand: Canon Pages: 214
Xerox DocuColor 5750 Reference Manual preview
DocuColor 5750
Brand: Xerox Pages: 7
Xerox DocuColor 2240 User Manual preview
DocuColor 2240
Brand: Xerox Pages: 36
Canon imageRunner Advance 6275 Basic Operation Gude preview
imageRunner Advance 6275
Brand: Canon Pages: 214

Brands by name

Popular brands

Load more brands