Toshiba DP1600 Service Handbook Download Page 37

Page: 37 / 239

December 2000 © TOSHIBA TEC

1 - 29

1600/2000/2500 ADJUSTMENT ITEMS

Data

6 (IO3)

I/O

E01008

7 (IO4)

I/O

E0100A

8 (IO5)

I/O

E02006

9 (IO6)

I/O

E02008

Bit

Input info.

BUCS

FDS2ON

FDS1ON

24VONOFF

COS1ON

IPCDET

PCDET

5ROMSEL

PSS3

FCOSON

PESON

LPSON

JCONECT

FSELECT

TESTMON

PMSTS

JPASSW

JJAMSW

JCOSON

JPOSON

JFLS2ON

JFLS1ON

Function

Reserved

Battery abnormal condition detection signal

EXT-SEN (Exit sensor)

FED-SEN (Feed sensor)

Cover open (Interlock SW) detection

TC-SW (Toner cartridge switch)

IPC PWA (Finisher) connection signal

PC-I/F PWA connection signal

RCVROM (MAIN recovery PWA) installation detection

CST-SW (Paper cassette switch)

FRCOV-SW (Front cover switch)

PE-SEN (Paper empty sensor)

Cassette 1

T-UP-SEN (Tray-up sensor)

Cassette 1

Connection of any of JSP or OCT

Reserved

Connection of BRIDGE COVER

Reserved

TNRE-SEN (Toner empty sensor)

Polygon motor synchronizing signal

Connection of OCT

Jam detection/jam detection/middle jam detection

JSP cover open/OCT cover open/BRIDGE COVER cover

open

Paper in upper stacker/-/BRIDGE COVER exit jam

detection

Upper stacker paper full/offset initial position/-

Lower stacker/paper full/paper full

Value

0: Normal

1: Battery abnormal condition

0: No paper

1: Paper detected

0: Paper detected

1: No paper

0: Closed 1: Open

0: With 1: Without

0: Connected

1: Not connected

0: Connected

1: Not connected

0: RCVROM installed

1: Not installed

0: Closed 1: Open

0: Paper loaded

1: Paper empty

0: Not lifted up 1: Lifted up

0: Connected

1: Not connected

0: BRIDGE COVER connected

1: JSP or OCT

0: Toner empty

1: Toner detected

0: Synchronous

1: Asynchronous

0: OCT connected

1: BRIDGE COVER or JSP

0: No paper 1: Paper present (JSP/OCT)
0: No paper
1: Paper present (BRIDGE COVER)

0: Cover closed

1: Cover open

0: No paper 1: Paper detected (JSP/OCT)
0: Paper detected
1: No paper (BRIDGE COVER)

0: Normal/non-initial

1: paper full/initial position

0: Normal 1: Paper full (JSP/OCT)

0: Paper full 1: Normal (BRIDGE COVER)

*1: The detection of the presence or absence of a toner cartridge is correctly displayed only when the front

cover is open.

*2: One of the three options is indicated (only one of them can be connect).

Summary of Contents for DP1600















































































































































































































































Search results

Summary of Contents for DP1600

Reviews:

Related manuals for DP1600

Brands by name

Popular brands

Toshiba DP1600, Service Handbook

Search results

Summary of Contents for DP1600

Reviews:

Related manuals for DP1600

Brands by name

Popular brands