Toshiba DP1600 Service Handbook Download

Page: 167 / 239

December 2000 © TOSHIBA TEC

4 - 43

1600/2000/2500 TROUBLESHOOTING

C57

Communication error between the IPC PWA and the CPU on the main PWA

1. Check the circuit patterns on the main PWA for short-circuits and breaks.

2. Check the IPC PWA for short-circuits and breaks.

3. Replace the IPC PWA.

4. Replace the main PWA.

C58

Communication error between the IPC PWA and the finisher

1. Check if the specified finisher is attached.

2. Check the IPC PWA for short-circuits and breaks.

3. Check if the pin of the connector being connected to the connector J2 on the IPC PWA is

disconnected or the harness is breaking.

4. Check if the fuse F3 of the power supply unit is blown.

5. Check the control PWA in the finisher for short-circuits and breaks.

6. Check the connections between the finisher and copier if the connector pins are discon-

nected, or the harnesses are breaking.

7. Replace the IPC PWA.

8. Replace the main PWA.

Summary of Contents for DP1600















































































































































































































































Search results

Summary of Contents for DP1600

Reviews:

Related manuals for DP1600

Brands by name

Popular brands

Toshiba DP1600, Service Handbook

Search results

Summary of Contents for DP1600

Reviews:

Related manuals for DP1600

Brands by name

Popular brands