Toshiba DP1600 Service Handbook Download Page 128

Page: 128 / 239

1600/2000/2500 TROUBLESHOOTING

4 - 4

December 2000 © TOSHIBA TEC

Is the exit sensor working? (using the test mode 04, Sensor Test, DATA No. 6 Bit 3)

1. Check if each connector between the exit sensor and relay PWA (CN45)

is disconnected.

2. Check if each connector pin is removed or the harness is broken.

3. Check if any conductor pattern on the relay and main PWA is open- or

short-circuited.

4. Replace the exit sensor.

5. Replace the relay PWA.

6. Replace the main PWA.

Check to see if there are any foreign obstacles on the recording paper path.

Near the JSP

Is the JSP paper jam sensor working? (using the test mode 04, Sensor Test, DATA No. 9

Bit 4)

1. Check if each connector between the JSP paper jam sensor and the

JSP PWA (CN262) is disconnected.

2. Check if each connector between the JSP PWA (CN260) and the relay

PWA (CN41) is disconnected.

3. Check if each connector pin is removed or the harness is broken.

4. Check if any conductor pattern on the JSP, relay and main PWA is

open- or short-circuited.

5. Replace the JSP paper jam sensor.

6. Replace the JSP PWA.

7. Replace the relay PWA.

8. Replace the main PWA.

Check to see if there are any foreign obstacles on the recording paper path.

YES

Summary of Contents for DP1600















































































































































































































































Search results

Summary of Contents for DP1600

Reviews:

Related manuals for DP1600

Brands by name

Popular brands

Toshiba DP1600, Service Handbook

Search results

Summary of Contents for DP1600

Reviews:

Related manuals for DP1600

Brands by name

Popular brands