Toshiba DP1600 Service Handbook Download Page 145

Page: 145 / 239

December 2000 © TOSHIBA TEC

4 - 21

1600/2000/2500 TROUBLESHOOTING

E45

Side cover of LCF opened during printing

Is the LCF side cover open?

Remove paper if there is any. Close the cover.

Is the LCF side cover open switch working? (using the test mode 04, Sensor Test, DATA No. 18

Bit4)

1. Check the connector of the LCF side cover open switch for disconnection.

2. Check the connectors CN100 and CN106 on the LCF PWA for disconnection.

3. Check the connector CN206 on the PFC PWA for disconnection.

4. Check the connector pins for disconnection and the harnesses for breaks.

5. Check the LCF PWA and PFC PWA for short-circuits and breaks.

6. Replace the LCF side cover opening/closing switch.

7. Replace the LCF PWA.

8. Replace the PFC PWA.

1. Replace the LCF side cover open switch.

2. Replace the LCF PWA.

3. Replace the PFC PWA.

YES

Summary of Contents for DP1600















































































































































































































































Search results

Summary of Contents for DP1600

Reviews:

Related manuals for DP1600

Brands by name

Popular brands

Toshiba DP1600, Service Handbook

Search results

Summary of Contents for DP1600

Reviews:

Related manuals for DP1600

Brands by name

Popular brands