Toshiba DP1600 Service Handbook Download

Page: 74 / 239

1600/2000/2500 ADJUSTMENT ITEMS

1 - 66

December 2000 © TOSHIBA TEC

1.5 Sharpness (HPF) Adjustment

If the user wants to change the image sharpness to softer or harder, adjust the HPF intensity in adjust

mode "05".

Image mode

Adjustment item

Photo/Text

Photo

Text

620

621

622

HPF intensity

Code

Power ON

Digital Keys

SET

Digital Keys

SET

INT

START

INT

Power OFF

(Enter code)

(Set the value)

(Test copy)

START

Notes:

1. Adjustment value is able to be input within the range of 0-99.

2. Default value.

Code

Default value

620

621

622

Remarks

No. of units: HPF table number

0: Use of default value

1: Text/Photo mode

2: Photo mode

3: Text mode

4-9: Unused

No. of tens: Filter combination intensity

0: Use of default value

1-9: Filter combination intensity

(The larger the intensity co-

efficient the stronger the in-

tensity.)

Summary of Contents for DP1600















































































































































































































































Search results

Summary of Contents for DP1600

Reviews:

Related manuals for DP1600

Brands by name

Popular brands

Toshiba DP1600, Service Handbook

Search results

Summary of Contents for DP1600

Reviews:

Related manuals for DP1600

Brands by name

Popular brands