Toshiba DP1600 Service Handbook Download Page 151

Page: 151 / 239

December 2000 © TOSHIBA TEC

4 - 27

1600/2000/2500 TROUBLESHOOTING

EA3 Paper remaining in finisher at power ON

Is there paper remaining on the transport path in the finisher?

Remove the paper.

Is the connector J10 on the finisher controller PWA disconnected?

Is the harness connecting the finisher controller PWA and inlet paper sensor broken?

Connect the connector securely. Replace the harness.

Is the inlet paper sensor working properly? (Check the movement of the actuator.)

1. Connect the connector of the inlet paper sensor securely.

2. Attach the actuator securely if its shaft is out of place.

3. Replace the inlet paper sensor.

Replace the finisher controller PWA.

EA4 Finisher front cover opened during printing

Is there paper remaining on the transport path in the finisher or main unit?

Remove the paper.

Is the finisher connected to the main unit?

Connect the finisher to the main unit.

Is the connector J11 on the finisher controller PWA disconnected?

Is the harness connecting the finisher controller PWA and finisher joint sensor broken?

Connect the connector securely. Replace the harness.

Is the inlet paper sensor working properly?

1. Connect the connector of the finisher joint sensor securely.

2. Replace the finisher joint sensor.

Replace the finisher controller PWA.

YES

Summary of Contents for DP1600















































































































































































































































Search results

Summary of Contents for DP1600

Reviews:

Related manuals for DP1600

Brands by name

Popular brands

Toshiba DP1600, Service Handbook

Search results

Summary of Contents for DP1600

Reviews:

Related manuals for DP1600

Brands by name

Popular brands