Toshiba DP1600 Service Handbook Download Page 201

Page: 201 / 239

December 2000 © TOSHIBA TEC

4 - 77

1600/2000/2500 TROUBLESHOOTING

(19) Moire/lack of sharpness

Step

Cause/Defect area

Density reproduction

Parameter adjustment

value

Measures

Adjust density.

Check adjustment value for sharpness.

Check items

Image density reproduction de-

fect?

Check image processing param-

eters.

eeding direction

Moire

Step

Cause/Defect area

Density reproduction

Parameter adjustment

value

Print section

Measures

Adjust density.

Check adjustment value for sharpness.

Check the above encircled area A and B, and

change the sharpness intensity in the sharp-

ness adjustment mode.

Check items

Image density reproduction de-

fect?

Check image processing param-

eters.

Adjust image processing param-

eters.

Lack of sharpness

Summary of Contents for DP1600















































































































































































































































Search results

Summary of Contents for DP1600

Reviews:

Related manuals for DP1600

Brands by name

Popular brands

Toshiba DP1600, Service Handbook

Search results

Summary of Contents for DP1600

Reviews:

Related manuals for DP1600

Brands by name

Popular brands