Toshiba DP1600 Service Handbook Download Page 179

Page: 179 / 239

December 2000 © TOSHIBA TEC

4 - 55

1600/2000/2500 TROUBLESHOOTING

4.1.18 Scanner related service call

F11

Scanner I/F error

1. Check if each connector between the scanner control PWA (CN6) and the main PWA (CN8)

is disconnected.

2. Check if each connector pin is removed or the harness is broken.

3. Check if any conductor pattern on the scanner control and main PWA is open- or short-

circuited.

4. Replace the scanner control PWA.

5. Replace the main PWA.

F12

Scanner unit program download write error

F13

Scanner unit program download sector error

1. Check if the recovery ROM PWA is firmly connected to the scanner control PWA (CN3).

2. Check if the connector pin is removed.

3. Check if any conductor pattern on the scanner control PWA is open- or short-circuited.

4. Replace the scanner control PWA.

F14

Scanner unit FROM error

Was the main PWA replaced?

Download the scanner total count value into the main PWA in the setting mode (08-

388).

Was the scanner unit or scanner control PWA replaced?

Download the scanner total counter value of the main PWA into the scanner con-

trol PWA in the setting mode (08-389).

1. Check if each connector between the scanner control PWA (CN6) and the main PWA (CN8)

is disconnected.

2. Check if each connector pin is removed or the harness is broken.

3. Check if any conductor pattern on the scanner control and main PWA is open- or short-

circuited.

4. Replace the scanner control PWA.

5. Replace the main PWA.

YES

Summary of Contents for DP1600















































































































































































































































Search results

Summary of Contents for DP1600

Reviews:

Related manuals for DP1600

Brands by name

Popular brands

Toshiba DP1600, Service Handbook

Search results

Summary of Contents for DP1600

Reviews:

Related manuals for DP1600

Brands by name

Popular brands