Toshiba DP1600 Service Handbook Download Page 208

Page: 208 / 239

December 2000 © TOSHIBA TEC

5 - 3

1600/2000/2500 UPDATING THE FIRMWARE

Fig 5-2-3

(5) Turn on the power.

Downloading of the main data starts.

The downloading status is displayed on the LCD of the copier as follows:

• Data is being downloaded from the ROM on the recovery PWA to the DRAM on the main PWA.

The number of displayed squares (

) increases.

Main PWA

Main recovery PWA

CN10

(4) Insert the main recovery PWA into CN10 of the main PWA, with the ROM mounting side facing down.

• Data is being stored in the flash ROM from the DRAM.

The number of displayed squares (

) decreases.

• Downloading is completed.

All dots are blinking.

Note:

It takes approx. 5 minutes to download the main data.

Number of downloaded data

1: Main data

( 2: Scanner data)

05-02-03

Summary of Contents for DP1600















































































































































































































































Search results

Summary of Contents for DP1600

Reviews:

Related manuals for DP1600

Brands by name

Popular brands

Toshiba DP1600, Service Handbook

Search results

Summary of Contents for DP1600

Reviews:

Related manuals for DP1600

Brands by name

Popular brands