manualshive.com logo in svg

Toshiba DP1600, Service Handbook

The Toshiba DP1600 Service Handbook is a comprehensive manual that provides detailed instructions for troubleshooting, repairing, and maintaining your Toshiba DP1600 product. Easily accessible as a free download from our website, this manual ensures you have the necessary information to maximize the performance of your device.

Share
Download
background image

December 2000  ©  TOSHIBA TEC

4 - 39

1600/2000/2500  TROUBLESHOOTING

4.1.10  Optical system service call

C21

Carriage initialization error

Is the wire or belt inside the scanner unit broken?  Does the wire or belt inside the scanner unit

unfasten?

Replace the wire or belt.

When the original glass is removed and the carriage is moved to the center, does the drive

system operate abnormally, such as racing or getting stuck?

Repair or replace the drive system.

Does the carriage move to the home position when the power is turned on?

1. Check if the home position sensor is not properly installed.

2. Check if the connector of the home position sensor is disconnected.

3. Check if the connector pin is removed or the harness is disconnected.

4. Check if any conductor pattern on the scanner control PWA is open- or short-

circuited.

5. Replace the home position sensor.

6. Replace the scanner control PWA.

7. Replace the main PWA.

1. Check if the scanner motor cable is damaged, short-circuited, or the connector pin is re-

moved.

2. Check if any conductor pattern on the scanner control PWA is open- or short-circuited.

3. Replace the scanner motor.

4. Replace the scanner control PWA.

5. Replace the main PWA.

YES

NO

YES

NO

YES

NO

Summary of Contents for DP1600
















































































































































































































































Reviews:

No comments

Related manuals for DP1600

QMS 3260 Quick Setup Manual preview
3260
Brand: QMS Pages: 8
Xerox 3001 Service Manual preview
3001
Brand: Xerox Pages: 360
Xerox C123 Copycentre Quick Installation Card preview
C123 Copycentre
Brand: Xerox Pages: 2
Olivetti d-Color MF2552 plus Service Manual preview
d-Color MF2552 plus
Brand: Olivetti Pages: 740
Canon iR1210 Service Bulletin preview
iR1210
Brand: Canon Pages: 104

Brands by name

Popular brands

Load more brands