Toshiba DP1600 Service Handbook Download Page 111

Page: 111 / 239

1600/2000/2500 PREVENTIVE MAINTENANCE

2 - 8

December 2000 © TOSHIBA TEC

*27. Magnetic roller

If a white banding appears on the magnetic roller, clean the area between the magnetic roller and

doctor blade with the doctor blade cleaning jig.

*28. Magnetic roller spacer

Confirm that the magnetic roller spacer is rotated. If not rotated, replace the magnetic roller spacer

with a new one.

*29. Drum gear/Cleaner paddle drive gear/Toner recovery auger drive gear

Confirm that toner or foreign matters is not stuck to the drum gear, cleaner paddle drive gear or

toner recover auger drive gear.

If stuck, remove the drum rear cover and clean the gear as required.

01/11

2-6

Doctor blade cleaning jig

Doctor blade

Magnetic roller

Drum rear cover

Drum assembly

Toner recovery auger

drive gear

Cleaner paddle

drive gear

Drum gear

2-7

*30. Doctor blade

Confirm that the doctor-sleeve gap is within the specified value. If not, adjust the gap. (For the

specified value and adjustment procedure, refer to section 1.13 “Adjustment of the doctor-sleeve

gap” on page 1-95.)

Summary of Contents for DP1600















































































































































































































































Search results

Summary of Contents for DP1600

Reviews:

Related manuals for DP1600

Brands by name

Popular brands

Toshiba DP1600, Service Handbook

Search results

Summary of Contents for DP1600

Reviews:

Related manuals for DP1600

Brands by name

Popular brands