Toshiba DP1600 Service Handbook Download Page 68

Page: 68 / 239

1600/2000/2500 ADJUSTMENT ITEMS

1 - 60

December 2000 © TOSHIBA TEC

Paper cassette

Cassette selection value

Code

Cassette 1

440

Cassette 2

441

Cassette 3/4

3/4

444

Bypass

442

LCF

443

(3) In order to set the distance "D" to 50 mm.

Notes:

1. An increase in the value increases the distance "D" (0.4 mm/step).

2. Adjustment value is able to be input within the range of 0 - 15. Default adjustment value is 8.

In case of the cassette 1 feeding (Code "440"), adjustment value is within the range of 0 - 40

(Default adjustment value is 23).

3. Since the cassette 1 adjustment value becomes a standard for all adjustments, this adjustment

must always be performed in the order stated above.

4. The adjustment is made for each paper cassette. Paper cassette selection values (1) and cor-

responding codes (3) in paper cassette adjustment.

5. To confirm the adjustment of ADU (code 445), do not print a test print in the procedure in (1),

but copy the TEST CHART.

Summary of Contents for DP1600















































































































































































































































Search results

Summary of Contents for DP1600

Reviews:

Related manuals for DP1600

Brands by name

Popular brands

Toshiba DP1600, Service Handbook

Search results

Summary of Contents for DP1600

Reviews:

Related manuals for DP1600

Brands by name

Popular brands