Toshiba DP1600 Service Handbook Download Page 124

Page: 124 / 239

December 2000 © TOSHIBA TEC

3 - 5

1600/2000/2500 PRECAUTIONS FOR STORING & HANDLING SUPPLIES

3.7

Checking and Cleaning of the Drum Cleaning Blade (SRU type)

(1) Handling Precautions

Since the edge of the cleaning blade performs the cleaning operation, pay attention to the followings:

•

Do not hit or rub the blade edge with anything hard.

•

Do not rub the edge with a dry cloth or soft pad.

•

Do not stain the edge with oil or fingerprints, etc.

•

Do not put solvents such as paint thinner or the blade.

•

Do not leave lint or dirt on the blade edge.

•

Do not put the blade close to a heat source.

(2) Cleaning

Clean the blade edge softly with a cloth soaked in water and afterwards squeezed hard.

01/11

Summary of Contents for DP1600















































































































































































































































Search results

Summary of Contents for DP1600

Reviews:

Related manuals for DP1600

Brands by name

Popular brands

Toshiba DP1600, Service Handbook

Search results

Summary of Contents for DP1600

Reviews:

Related manuals for DP1600

Brands by name

Popular brands