Toshiba DP1600 Service Handbook Download Page 100

Page: 100 / 239

1600/2000/2500 ADJUSTMENT

1 - 92

December 2000 © TOSHIBA TEC

1.11 Measurement of Transfer Guide Bias

The transfer charger bias is applied to the pinch roller and the paper guide plate to prevent the transfer

charger charge from escaping through the recording paper during transfer. To analyze the cause of a

transfer failure which has occurred, you can output the transfer guide bias in the output test at any time

and then measure the voltage.

Important:

Measure the transfer guide bias with the toner cartridge and the process unit taken out from the copier

and the front cover open. Also, keep the front cover switch and interlock switch (front cover) ON by using

the switch jigs (big/small).

<Keys used in operation>

<Display messages and measurement methods >

: Enter the "Developer Bias Transformer ON/OFF" code.

Important:

Before outputting the transfer guide bias, it is necessary to turn

the developer bias ON.

: Developer bias ON

Warning:

High voltage is output from the developer bias terminal. NEVER

touch the terminal while measuring.

FUNCTION TEST
09.CODEC TEST
10.OUTPUT TEST
11.PRINTER BOARD TEST

Power ON

10.OUTPUT TEST

SET

CANCEL

START

01-11-01

SET

To next page

: Enter the "Transfer Guide Bias ON/OFF" code.

Developer bias measuring plate

SET

Summary of Contents for DP1600















































































































































































































































Search results

Summary of Contents for DP1600

Reviews:

Related manuals for DP1600

Brands by name

Popular brands

Toshiba DP1600, Service Handbook

Search results

Summary of Contents for DP1600

Reviews:

Related manuals for DP1600

Brands by name

Popular brands