Toshiba DP1600 Service Handbook Download Page 25

Page: 25 / 239

December 2000 © TOSHIBA TEC

1 - 17

1600/2000/2500 ADJUSTMENT ITEMS

Code

618

620

635

641

642

648

649

650

652

665

673

685

688

689

Factor

F/W

Setting item

Default setting for mixed size originals

0: OFF
1: ON

* Setting 08-618 to 1 (ON) and 08-641 to

4 (alternate) simultaneously is not al-
lowed.

APS forced start (Exclude RADF)

0: Valid (One time pressing)
1: Reserved
2: Invalid

Process for last page (one-sided original)
at duplex copying
0: One-side copy
1: Double-sided copy (blank paper is

added to as the last even numbered
page to output the copy in the same
orientation with previous pages.)

Auto sort mode (when document is loaded
into DF)
Also set on panel.

0: Invalid 1: Staple 2: Sort 3: Invalid
4: Vertical and horizon. alternate
5: Sort offset

* Setting 08-641 to 4 (alternate) and 08-

618 to 1 (ON) simultaneously is not al-
lowed.

Sorter mode priority selection (at all clear)
Also set on panel.

0: NON SORT 1: STAPLE 2: SORT
3: Reseved 4: ALTERNATION
5: SORT OFFSET
6: NON SORT OFFSET

Initialization of finisher bin at all clear

0: Valid 1: Invalid

Magazine sort setting

0: Left-hand open 1: Right-hand open

2in1/4in1 setting

0: Horizontal write 1: Vertical write

Cascade operation setting (DP2000/2500
series)

0: No cascade
1: 1

→

2 (Endless stack included)

2. Reserved

Set PPC area default.

05: Adjust area,

adjust store area

08: Setting (PPC-FUNC) area
(Except the counter values)

Resetting drum-related counters,
08-355, 08-401.
(Valid when 08-689 is set to 1, SRU)
Paper feeding by turns at duplex copying
0: Invalid 1: Valid
UI shortcut key
0: Invalid
1: Valid (REDUCE/ENLARGE and ZOOM

UP/DOWN only)

2: Valid (Cassette paper size setting only)
3: Valid (All, REDUCE/ENLARGE, ZOOM

UP/DOWN, and cassette paper size
setting)

SRU/CRU mode setting

0: CRU 1: SRU

Mode

PPC

Memory

PPC

ALL

Expansion

PPC

Expansion

PPC

Expansion

PPC

Self-

check

Self-

check

PPC

ALL

Acceptable

value *1

0-1

0-2

0-1

0-5

0-6

0, 1

0-1

0-2

0-1

0-4

0-1

Refer to

page

1-90

02/07

Image

quality

mode

Default

*1 : The entry of code enables automatic execution.

Summary of Contents for DP1600















































































































































































































































Search results

Summary of Contents for DP1600

Reviews:

Related manuals for DP1600

Brands by name

Popular brands

Toshiba DP1600, Service Handbook

Search results

Summary of Contents for DP1600

Reviews:

Related manuals for DP1600

Brands by name

Popular brands