Toshiba DP1600 Service Handbook Download Page 200

Page: 200 / 239

1600/2000/2500 TROUBLESHOOTING

4 - 76

December 2000 © TOSHIBA TEC

Step

Cause/Defect area

Density/Gray balance

Printer section

Scanner

Printed image

Measures

Adjust density.

Go to step 4 if there is any problem on image.

Clean them.

Perform troubleshooting for faded image.

Perform troubleshooting for background fog-

ging.

Perform troubleshooting for blotch image.

Perform troubleshooting for poor fusing.

Check items

Check density/gray balance.

Check test print image (Code

113).

Original glass, mirrors or lens fil-

ter dirty?

Is there any faded image (low

density)?

Is there any fog in background?

Is there any botch image?

Is there any transfer defect?

(18) Defect of image density/Gray balance

eeding direction

Image density

Gray balance

Summary of Contents for DP1600















































































































































































































































Search results

Summary of Contents for DP1600

Reviews:

Related manuals for DP1600

Brands by name

Popular brands

Toshiba DP1600, Service Handbook

Search results

Summary of Contents for DP1600

Reviews:

Related manuals for DP1600

Brands by name

Popular brands