Toshiba DP1600 Service Handbook Download

Page: 218 / 239

December 2000 © TOSHIBA TEC

5 - 13

1600/2000/2500 UPDATING THE FIRMWARE

5.3.2 Downloading

Download the firmware by using the download disks (Disks 1 and 2) created in the procedure of “5.3.1

Creating Download Disks”

Important:

• The download program cannot be run normally at the MS-DOS prompt after Windows

95/98 is started. Once end Windows, insert the download disk (Disk 1) in the drive, and

turn the power ON to directly start the program from the floppy disk.

• While the data is being updated, do not turn the copier or PC power OFF, or the data

may be destroyed and the copier may fail to operate normally.

• Do not remove the floppy disk from the drive until you are instructed to do so. The disk

or drive may be damaged.

(1) Insert the download disk (Disk 1) in the floppy disk drive and turn the PC power ON.

The download menu screen appears.

05-03-016

Summary of Contents for DP1600















































































































































































































































Search results

Summary of Contents for DP1600

Reviews:

Related manuals for DP1600

Brands by name

Popular brands

Toshiba DP1600, Service Handbook

Search results

Summary of Contents for DP1600

Reviews:

Related manuals for DP1600

Brands by name

Popular brands