Toshiba DP1600 Service Handbook Download

Page: 126 / 239

1600/2000/2500 TROUBLESHOOTING

4 - 2

December 2000 © TOSHIBA TEC

4.1 Troubleshooting Based on Error Code

4.1.1 Transporting jam in the main body

E01

Paper jam inside the machine

E02

Paper jam near the fuser unit

When recording paper is left inside the machine, remove it. If this error occurs frequently, the

following items should be checked.

Where was the paper stopped?

Before reaching the registration roller

Is the registration roller clutch working? (using the test mode 10, Output Test, CODE 108)

Check to see if there are any foreign obstacles on the recording paper path

near the registration roller.

1. Check if each connector between the registration roller clutch and relay PWA (CN37)

is disconnected.

2. Check if each connector pin is removed or the harness is broken.

3. Check if any conductor pattern on the relay and main PWA is open- or short-circuited.

4. Replace the registration roller clutch.

5. Replace the relay PWA.

6. Replace the main PWA.

Near the fuser unit

Is the HR drive gear 1 of the fuser unit driven when the main motor is manually rotated

clockwise?

Check to see if there are any foreign obstacles on the recording paper path

near the fuser unit.

1. Check to see if the gear in the fuser unit is damaged.

2. Check to see if each gear of the main drive gear assembly is damaged.

YES

Summary of Contents for DP1600















































































































































































































































Search results

Summary of Contents for DP1600

Reviews:

Related manuals for DP1600

Brands by name

Popular brands

Toshiba DP1600, Service Handbook

Search results

Summary of Contents for DP1600

Reviews:

Related manuals for DP1600

Brands by name

Popular brands