Customer Expectation Setting Document for
Document Centre ColorSeries 50
December 12, 2001
Space Requirements / Service Space Envelope
The dimensions shown below are in inches and are absolute
minimums.
Moveable
Configurations for Document
Centre ColorSeries 50
Width
(in.)
Depth (in.)
Document Centre ColorSeries
50 with or without High Capacity
Offset Output Tray
(Base unit)
68.5”
71.5” Room or
86.5” Hallway
Base unit + High Capacity
Feeder
98.5”
71.5” Room or
86.5” Hallway
Base unit + Mailbox/Sorter or In-
line Stapler Finisher
111”
71.5” Room or
86.5” Hallway
Base unit + High Capacity
Mailbox/Sorter
141”
71.5” Room or
86.5” Hallway
Base unit + High Capacity
In-line Stapler Finisher
141”
71.5” Room or
86.5” Hallway
Base unit + Edit Pad
100.5”
71.5” Room or
86.5” Hallway
Base unit + High Capacity
Edit Pad
130.5”
71.5” Room or
86.5” Hallway
Base unit + Mailbox/Sorter or In-
line Stapler Fi Edit Pad
with or without High Capacity
Feeder
176”
71.5” Room or
86.5” Hallway
Electrical Requirements
Western Hemisphere
Single Phase
2 wire, earth ground
16 ampere
Line to Neutral Service
105 – 127 volts AC
20 ampere
Receptacles (or equivalents)
Xerox Part Number
NEMA Part No. 5-20R
600S3703
Frequency
60 HZ single phase
Power Cord Length
10 feet
The Western Hemisphere
Document Centre ColorSeries 50
requires sole use of 20 ampere
outlet, which is standard in most
modern office buildings. Consult
the diagram (right side) to confirm
the existence of this outlet in the
proposed installation space
Ground Fault Protection is provided which meets Xerox safety
requirements and exceed the Industry Standards for Information
Technology Equipment.
Installation Considerations
•
Physical delivery of the Document Centre ColorSeries 50 will be
by a Xerox authorized “Delivery/Removal” carrier. The carrier will
install and perform a functional check of the copier unit. The
carrier will review the “Getting to know your product” package and
provide software/documentation to the customer. The customer
is responsible for connecting equipment on their network.
•
Carpeted flooring surfaces may require the installation of a
mobility plate to allow the product to be moved during normal
maintenance activities.
•
There should be a minimum of 78 inches (1,981 mm) clearance
from the floor to the nearest overhead obstruction.
•
The unit weights 477 lbs. (217 kg).
Environmental Requirements
Minimum
Maximum
Temperature
50º F (10º C)
95º F (35º C)
Humidity
15% RH
85% RH
Heat Emission
1,230 BTU/Hr
(Standby)
3,755 BTU/Hr
(Running)
Power Consumption
800 VA*
(Standby)
1,200 VA*
(Running 4-color)
Altitude (above sea level)
0
10,000 ft. (3,050
meters)
Voltage
105
127
Low Power Mode Power
Usage
-
150 Watts
Low Power Mode Recovery
Time
-
30 seconds
* Stated as an average. Warm up power consumption is 1,600 VA.
Energy Star
The Document Centre ColorSeries 50 is Energy Star certified. This
means that the machine automatically switches to a Low Power mode
after an idle period. After an additional idle period, the device
automatically powers off, saving additional power. The customer can
adjust the “Time to Low Power mode” and the “Time to Auto Power
Off” as described in the System Administration Guide.
Operating Supplies
The Xerox Supplies Marketing Center, 1-800-822-2200 US, 1-800-668-
1099 CAN (English), 1-800-668-0133 CAN (French) is available for
ordering Xerox supplies, including paper and other throughput
material.
US Customers on Metered Price Plans should call Metered Hotline,
U.S., 1 – 800 – 599-2198 for their dry ink and fuser oil.
Item
Reorder
#
Units per
Carton
Dry Ink - Black
6R945
4 Cartridges
Dry Ink - Cyan
6R946
4 Cartridges
Dry Ink - Magenta
6R947
4 Cartridges
Dry Ink - Yellow
6R948
4 Cartridges
Fuser Oil
8R7975
1 Cartridge
Staples (for optional
convenience stapler)
108R152
3 Cartridges
5000 staples
per cartridge
Staples (for optional
in-line stapler finisher)
8R12724
3 Staple
Packs
5000 staples
per pack
Dry Ink and Fuser consumption will vary depending on image, area
coverage and media
