Thermo Scientific Orion 2111LL User Manual Download Page 30

Page: 30 / 118

III-

Instrument Operation

Thermo Scientific Orion 2111LL Sodium Monitor User Guide

ROSS and the COIL tradedress are trademarks of Thermo Fisher Scientific Inc. US Patent 6,793,787

Icon

Parameter/Mode

Action

Operational Selections

Enters

calibration

mode

Calibration mode with user prompts

DKA, Offline

Scroll

numbers

Scroll

cal

setup

mode

Used to edit values
Use to select available modes by using up arrow.

0-9 selectable by digit, first digit selectable 0-19

Enters

setup

mode

System setup mode at the last parameter used

by the customer.

DKA, Password, Date, Time, Log, Hold, Reset, Display,

Measure, Temp, Alarm, mAmp, Test, Calibration

Move cursor to the

right

digit

Used to edit values

When move to final digit, system will wrap around to

first digit

Enters

test

mode

Use enter key to advance through sequence

of displays
Diagnostics will appear in top right of screen

Last calibration slope & E

, error list, log points by time

& date, error log by time & date, software rev., serial #,

displays measured mV and noise, mAmp output values

(sensor & temp), and display test

Scroll

down

numbers

Scroll

down

cal

setup

mode

Used to edit values that can be changed

by the operator
Use to select available modes by using down arrow

0-9 selectable by digit, first digit selectable 0-19

view

Log-changes between date and data that was

logged at that specific time interval

Use to view data in calibration, measurement &

status logs

+/-

Toggles negative/positive sign when editing

numbers

enter

function

Accepts value or selection displayed on LCD,

stores in memory

enter

(in

test

mode Only)

Used in test mode to display additional

information for selected menus

exit to measure

Exits from setup or cal modes and puts the

monitor into sample mode.

Instrument automatically enters sample mode when

first turned on and after calibration.

last Screen

Used in test and setup mode

User may move back to previous menu.

Can not be used in calibration mode: If exit calibration,

user must re-do calibration

decimal

point

Sets the decimal point position in some

menus with decimal point numbers between toggles

ppm & ppb.

Used in set decimal position

Description of

Keypad Icons

Figure III-

Keypad Icons

上海肯强贸易有限公司
http://www.kq17.com.cn

Summary of Contents for Orion 2111LL























































































































Search results

Summary of Contents for Orion 2111LL

Reviews:

Related manuals for Orion 2111LL

Brands by name

Popular brands

Thermo Scientific Orion 2111LL, User Manual

Search results

Summary of Contents for Orion 2111LL

Reviews:

Related manuals for Orion 2111LL

Brands by name

Popular brands