manualshive.com logo in svg

Thermo Scientific Orion 2111LL, User Manual, Page: 64 / 118

Share
Download
Thermo Scientific Orion 2111LL User Manual Download Page 64

IV-5

Calibration

Thermo Scientific Orion 2111LL Sodium Monitor User Guide

ROSS and the COIL tradedress are trademarks of Thermo Fisher Scientific Inc. US Patent 6,793,787

Maximum .system .accuracy .is .ensured .through .a .fast, .easy, .and .accurate .

calibration .performed .in .the .expected .sample .range . . .This .calibration .

procedure .uses .equipment .supplied .in .calibration .kit .(Cat . .No . .181148) . .

• . Perform .monthly .maintenance .procedure .including .conditioning .of .

electrode . .

• . Wait .at .least .one .hour .after .changing .reagent .or .etching .electrode . .

Calibration .must .be .initiated .within .2-3 .hours .of .electrode .etching .to .

ensure .faster .response . .

• . Check .that .present .sample .concentration .is .equal .or .less .than .standard .

1 .(10 .ppb); .if .not, .calibration .can .still .be .performed .with .a .loss .in .

accuracy .as .long .as .background .concentration .is .not .significantly .

larger . . .Accuracy .can .be .attained .if .alternate .standards .are .employed .but .

standard .1 .should .not .be .less .than .10 .ppb .

• . Proper .pipette .technique .is .crucial .to .calibration . . .If .operator .is .not .

familiar .with .pipette .equipment .or .technique, .refer .to .

Appendix A-11, 

Pipette Operation

 .

• . Do .not .touch .pipette .tip .with .bare .fingers . . .Risk .of .sodium .

contamination .is .possible . . .Use .powder .free .gloves .to .prevent .

contamination . .

• . When .using .pipette .to .inject .standards .during .calibration, .use .fresh .

pipette .tip .for .each .standard .concentration .and .each .injection .

• . With .a .fresh .tip .installed, .rinse .the .tip .with .the .same .concentration .as .

the .intended .injection . .

• . Fill .the .tip .and .dispense .the .tip .with .the .standard .1-3 .times . . .

Be sure to 

discard the standard in the drain, between the rinses.

• . Wipe .any .excess .liquid .from .the .outside .of .the .tip .with .out .touching .

the .opening .

• . Insert .pipette .tip .into .calibration .port .on .flow .cell .cap . . .

• . Be .sure .to .hold .pipette .completely .vertical .while .dispensing . . .Do .not .

inject .standard .on .side .of .flow .cell, .as .a .film .may .be .retained .on .the .

inside .of .the .wall .resulting .in .errors .in .precision .of .calibration . . .Refer .to .

Figure IV-5

 .

Before Performing 

DKA Calibration

Figure IV-5 

Pipette Dispensing

Recommendations

 上海肯强贸易有限公司 
http://www.kq17.com.cn

Summary of Contents for Orion 2111LL























































































































Reviews:

No comments