Thermo Scientific Orion 2111LL User Manual Download Page 78

Page: 78 / 118

V-3

Instrument Maintenance

Thermo Scientific Orion 2111LL Sodium Monitor User Guide

ROSS and the COIL tradedress are trademarks of Thermo Fisher Scientific Inc. US Patent 6,793,787

1 . . . If .sample .flow .can .be .adjusted .with .the .pressure .regulator .to . .

50 .mL/minute .or .more, .skip .this .procedure . .

2 . . . Turn .off .sample .flow .by .turning .the .inlet .valve .to .the .right . .

3 . . . Remove .filter .hex .cap .using .1-inch .open-ended .wrench . .

4 . . . Separate .filter .cap .with .bypass .valve .assembly .from .filter .body, . .

retaining .ring .

5 . . . Remove .filter .element .and .soft .gasket . .(if .necessary) .

6 . . . Replace .gasket .and .press .new .sintered .element .into .filter .body . .

7 . . . Replace .hex .cap .and .bypass .valve .assembly .and .reposition .bypass .drain .

line .into .drain .assembly .

8 . . . Retighten .hex .cap .to .approximately .75 .pound-inch .in .torque . .

9 . . . Turn .on .sample .flow .by .1⁄4 .turn .of .inlet .valve .to .the .left . .

10 . .Check .for .leaks . .

Warning:

Replacement .of .DIPA .reagent .is .dependent .on .operating .

conditions .and .usage . . .Replacement .may .occur .as .long .as .60 .days .from .

installation . . .Be .sure .to .monitor .the .DIPA .levels .weekly .to .assess .proper .

replacement .schedule . . .DIPA .is .hazardous . . .Use .protective .glasses .and . .

gloves . . .Refer .to .bottle .label .and .MSDS .for .precautions . . .Work .in .a . .

well-ventilated .area . .

Danger:

Turn .off .the .air .pump .before .beginning .procedure; .otherwise, .the .

air .pump .will .spatter .caustic .reagent .outward .as .bottle .is .removed . . .

Refer .to .

Chapter III, Use of Setup Mode

for .instructions .to .turn .air .pump .

On/Off . .

1 . . . Remove .thumbnut .and .slide .reagent .bottle/adaptor .from .manifold .

assembly . .

2 . . . Unscrew .bottle .cap, .and .lift .adaptor .from .bottle . .

Replacement Sample

Inlet Filter

Replacement of DIPA

Reagent and Diffusion

Tubing Assembly

上海肯强贸易有限公司
http://www.kq17.com.cn

Summary of Contents for Orion 2111LL























































































































Search results

Summary of Contents for Orion 2111LL

Reviews:

Related manuals for Orion 2111LL

Brands by name

Popular brands

Thermo Scientific Orion 2111LL, User Manual

Search results

Summary of Contents for Orion 2111LL

Reviews:

Related manuals for Orion 2111LL

Brands by name

Popular brands