Thermo Scientific Orion 2111LL User Manual Download Page 50

Page: 50 / 118

III-

Instrument Operation

Thermo Scientific Orion 2111LL Sodium Monitor User Guide

ROSS and the COIL tradedress are trademarks of Thermo Fisher Scientific Inc. US Patent 6,793,787

Default

User Action

Marquee

Scrolling

Main Display

top line

bottom line

Notes

mAMP (cont’d)

Press

to accept value and advance to next

screen for temperature output (tOUt)

SET TEMP OUTPUT VALUE

tOUt
(Flashing)

Press

to set tOUt low (LO) limit

5 .0 C

mA TEMP OUTPUT LOW

VALUE

LO
#.# C
(Flashing)

To set tOUt low (LO) limit value:
Press

to set digit values

Press

arrow to move to set next digit

Press

to set a positive or negative

temperature value

mA TEMP OUTPUT LOW

VALUE

#.# C

(Flashing digit will change)

Press

to accept values and advance to next

screen to set tOUt high value

45 C

mA TEMP OUTPUT HIGH
VALUE

HI
# #.# C
(Flashing)

To set tOUt high (HI) limit value:
Press

to set digit values

Press

arrow to move to set next digit

mA TEMP OUTPUT HIGH

VALUE

##. # C

(Flashing digit will change)

Press

to return user to main setup menu for

mAMP submenu

mAMP
(Flashing)

SEL
SCrn

Press

to scroll to next menu

上海肯强贸易有限公司
http://www.kq17.com.cn

Summary of Contents for Orion 2111LL























































































































Search results

Summary of Contents for Orion 2111LL

Reviews:

Related manuals for Orion 2111LL

Brands by name

Popular brands

Thermo Scientific Orion 2111LL, User Manual

Search results

Summary of Contents for Orion 2111LL

Reviews:

Related manuals for Orion 2111LL

Brands by name

Popular brands