Thermo Scientific Orion 2111LL User Manual Download Page 68

Page: 68 / 118

IV-9

Calibration

Thermo Scientific Orion 2111LL Sodium Monitor User Guide

ROSS and the COIL tradedress are trademarks of Thermo Fisher Scientific Inc. US Patent 6,793,787

Stage

User Action

Marquee

Main Display

top line

bottom line

Valve position

Wait 0 - 5 minutes

AWAITING DATA

STABILITY

Actual readings in ppb

& mV flashing

System continuously evaluates

data by applying stability criteria

until a “stable/pass” condition is

met. If system stabilizes follow

stage 8

If system stability is not reached

a timeout occurs. Error E041 is

issued. Jump to step

Error E04

No action necessary

System calculates new Eo and

slope and checks for errors. If

no errors are found follow

stage 9

If there is a slope/E

or other

cal data related error, jump to

appropriate error code.

Press

to accept the new

slope and Eo values
or
Press

to abort calibration.

The values will not be stored. The

last saved values for calibration

prior to the aborted values will be

used in measurement mode.

NEW CALIBRATION

SLOPE AND E

PRESS ENTER TO

ACCEPT OR PRESS EXIT

TO ABORT WITHOUT

SAVING.

Calculated Slope and E

System presents the new slope

and E

values.

is pressed, continue to

stage 30

is pressed, refer to step

Exit

Exit 4

, depending on

the system software revision.

Some system software revisions

will not display the following

sections that are highlighted in

gray

NEW CALIBRATION

SLOPE AND E0 SAVED.

PRESS ENTER

CAL StOr

Calibration values for Slope and

Eo are stored.
Successful calibration

completed.

Press

上海肯强贸易有限公司
http://www.kq17.com.cn

Summary of Contents for Orion 2111LL























































































































Search results

Summary of Contents for Orion 2111LL

Reviews:

Related manuals for Orion 2111LL

Brands by name

Popular brands

Thermo Scientific Orion 2111LL, User Manual

Search results

Summary of Contents for Orion 2111LL

Reviews:

Related manuals for Orion 2111LL

Brands by name

Popular brands