Thermo Scientific Orion 2111LL User Manual Download Page 29

Page: 29 / 118

III-

Thermo Scientific Orion 2111LL Sodium Monitor User Guide

ROSS and the COIL tradedress are trademarks of Thermo Fisher Scientific Inc. US Patent 6,793,787

Chapter III

Instrument Operation

Description of

Basic Unit Controls

Figure III-

Faceplate

Parameter

Location on Display

Options

Default

Mode Indicator

Top right corner

Hold, Cal, Setup, Measure, Diagnostic Measure

Marquee Display

Top left corner

Customer prompts through scrolling

messaging

No ATC connected 25 ˚C

ATC connected:

measured at actual

Temperature Display

Top left corner

Celsius

Measured at actual

Main Data Display

Middle Line:

Lower Line:

Concentration

conc in ppb

9999:

At initial installation if no

electrodes are connected: Connect

electrodes and calibrate
Lower line will be disabled at

installation. Refer to use of setup mode

to initiate lower line visibility.

Measurement Units

Left & right side of display

ISE concentration ppb/ppm

Auto ranging:

ppb - ppm

System Status

Yellow /Green Indicator Light:

Left side of display above

View icon

Green:

System OK

Yellow:

System warning

Yellow:

Needs calibration

System Error

Red Indicator Light:

Right side of display above

Setup icon

Red:

System failure

Red:

At initial installation, needs

electrodes installed and calibration.

上海肯强贸易有限公司
http://www.kq17.com.cn

Summary of Contents for Orion 2111LL























































































































Search results

Summary of Contents for Orion 2111LL

Reviews:

Related manuals for Orion 2111LL

Brands by name

Popular brands

Thermo Scientific Orion 2111LL, User Manual

Search results

Summary of Contents for Orion 2111LL

Reviews:

Related manuals for Orion 2111LL

Brands by name

Popular brands