Thermo Scientific Orion 2111LL User Manual Download Page 117

Page: 117 / 118

A-11

Appendix

Thermo Scientific Orion 2111LL Sodium Monitor User Guide

ROSS and the COIL tradedress are trademarks of Thermo Fisher Scientific Inc. US Patent 6,793,787

To help eliminate the risk of contamination, each pipette is fitted with a tip

ejector system. The tip ejector system consists of a soft-touch tip ejector and

specially designed gearing mechanism. To release the tip, point the pipette

at suitable waste receptacle and press the tip ejector with your thumb.

You can attach the pipette shelf hanger on a counter, pipette stand or

anywhere where you want to hang your pipette.

Clean the area where you plan to attach the shelf hanger. Apply two stickers

to the underside of the shelf hanger. Press the shelf hanger firmly into place

– on a shelf, counter top or pipette stand. To use, hang the grippy finger

rest on the shelf hanger.

Pipette Operation

Tip ejection

上海肯强贸易有限公司
http://www.kq17.com.cn

Summary of Contents for Orion 2111LL























































































































Search results

Summary of Contents for Orion 2111LL

Reviews:

Related manuals for Orion 2111LL

Brands by name

Popular brands

Thermo Scientific Orion 2111LL, User Manual

Search results

Summary of Contents for Orion 2111LL

Reviews:

Related manuals for Orion 2111LL

Brands by name

Popular brands