Thermo Scientific Orion 2111LL User Manual Download Page 94

Page: 94 / 118

VI-3

Troubleshooting

Thermo Scientific Orion 2111LL Sodium Monitor User Guide

ROSS and the COIL tradedress are trademarks of Thermo Fisher Scientific Inc. US Patent 6,793,787

Malfunction

Possible Cause

Remedy

Over-Range

Readings

Electrode connections

Verify electrode connections to electrode

cables. Silde electrode cable back to expose

male connector. Be sure to secure female

connector on electrode to male connector

before twisting to tighten. Refer to

Chapter II

Electrode wiring

Electrodes not properly wired to terminal

strip. Refer to

Chapter II

Reference electrode

Missing or blocked filling solution. Refer to

Chapter II

Electrode failure

Electrodes are shorted, cracked, damaged.

Install new probes. Refer to

Chapter II

Electronics failure /

Bad setup /

Needs calibration

Try resetting the monitor. Refer to

Chapter VI

Default

Power loss while back-

up battery was not fully

charged

Allow battery to charge overnight.

Recalibrate and reprogram. Refer to

Chapter IV

Battery failure

Contact Customer Support for Orion products

at 1-800-225-1480

Electronics failure

Try resetting the monitor. Refer to

Chapter VI

or contact Customer Support for

Orion products at 1-800-225-1480

Low Readings

Instrument okay. Sample

very pure

Perform span check procedure. If span check

passes, instrument is okay and sample is

very pure. Refer to

Chapter IV

Electronics failure

Try resetting the monitor. Refer to

Chapter VI

or contact Customer Support for

Orion products at 1-800-225-1480

If offline calibration performed, verify

accuracy of alternate method value.

Refer to

Chapter IV

上海肯强贸易有限公司
http://www.kq17.com.cn

Summary of Contents for Orion 2111LL























































































































Search results

Summary of Contents for Orion 2111LL

Reviews:

Related manuals for Orion 2111LL

Brands by name

Popular brands

Thermo Scientific Orion 2111LL, User Manual

Search results

Summary of Contents for Orion 2111LL

Reviews:

Related manuals for Orion 2111LL

Brands by name

Popular brands