Thermo Scientific Orion 2111LL User Manual Download Page 71

Page: 71 / 118

IV-

Calibration

Thermo Scientific Orion 2111LL Sodium Monitor User Guide

ROSS and the COIL tradedress are trademarks of Thermo Fisher Scientific Inc. US Patent 6,793,787

Stage

User Action

Marquee

Main Display

top line

bottom line

Valve position / Notes

Stability Timeout

Error 4

Decide to continue calibration

despite instability or abort

READINGS WERE

UNSTABLE. PRESS

ENTER TO CONTINUE

CALIBRATION OR

PRESS EXIT TO ABORT

E041

Stability was not reached before

timeout
If

is pressed system will

continue from step where stability

timed out.
If

is pressed refer to

Exit

Exit 4,

depending on the system

software revision

Calibration Error

Error 4

Review Marquee text to

understand the failure that

occurred

INVALID (NEGATIVE)

SLOPE
PRESS ENTER TO

ABORT CALIBRATION

E042

Invalid slope continue at

Exit 3

Error 09

Review Marquee text to

understand the failure that

occurred

BAD SLOPE
PRESS ENTER

E109

Bad Slope
Press

to continue at

stage 9

Error 5

Review Marquee text to

understand the failure that

occurred

BAD E

PRESS ENTER

E125

Bad E

Press

to continue at

stage 9

上海肯强贸易有限公司
http://www.kq17.com.cn

Summary of Contents for Orion 2111LL























































































































Search results

Summary of Contents for Orion 2111LL

Reviews:

Related manuals for Orion 2111LL

Brands by name

Popular brands

Thermo Scientific Orion 2111LL, User Manual

Search results

Summary of Contents for Orion 2111LL

Reviews:

Related manuals for Orion 2111LL

Brands by name

Popular brands