manualshive.com logo in svg

Thermo Scientific Orion 2111LL, User Manual, Page: 41 / 118

Share
Download
Thermo Scientific Orion 2111LL User Manual Download Page 41

III-3

Instrument Operation

Thermo Scientific Orion 2111LL Sodium Monitor User Guide

ROSS and the COIL tradedress are trademarks of Thermo Fisher Scientific Inc. US Patent 6,793,787

Default User Action

Marquee 

Scrolling

Main Display

top line

bottom line

Notes

LOG

LOG 
(flashing)

SEL
SCrn

Press 

 to set log interval

0 0 : 0 0

SET LOG TIME IN HOUR 

MINUTES

# #: ##  
LOg
(All digits flashing)

Press 

 / 

 to set first digit

SET LOG TIME IN HOUR 

MINUTES

#

 # : # # 

LOg
(Flashing digit will 

change)

To disable the log 

enter 0000 for log 

interval 
The minimum log 

interval is 5 minutes
The maximum log 

interval is 99 hours 

and 59 minutes

Press 

 to move to set each digit 

SET LOG TIME IN HOUR 

MINUTES

# 

#

 : # # 

LOg
(Flashing digit will 

change)

Press 

 / 

 to set values 

of remaining digits for log interval

SET LOG TIME IN HOUR 

MINUTES

# # : # 

#

 

LOg
(Flashing digit will 

change)

Press 

 to return user to main setup 

menu for LOG submenu

LOG
(Flashing)

SEL
SCrn

Press 

 to scroll to next menu

 上海肯强贸易有限公司 
http://www.kq17.com.cn

Summary of Contents for Orion 2111LL























































































































Reviews:

No comments