Thermo Scientific Orion 2111LL User Manual Download Page 66

Page: 66 / 118

IV-7

Calibration

Thermo Scientific Orion 2111LL Sodium Monitor User Guide

ROSS and the COIL tradedress are trademarks of Thermo Fisher Scientific Inc. US Patent 6,793,787

Stage

User Action

Marquee

Main Display

top line

bottom line

Valve position /

Notes

Turn Diverter Valve to

cal

position

Arrow pointing up

TURN DIVERTER VALVE SO

ARROW POINTS UP
PRESS ENTER

FILL FCEL

Press

Wait 60 minutes

WAIT 60 MINUTES

Actual readings in

ppb & mV flashing

Minutes will be counted

down on Marquee.

Marquee will display

PRESS ENTER after 60

minutes.

Press

Turn Left Air Valve to

calibrate

position. Arrow pointing up
Turn Right Air Valve to

calibrate

position. Arrow pointing up

TURN LEFT AND RIGHT VALVES

UP
PRESS ENTER

Alr

Press

When liquid level in the flow

cell has risen above the siphon

tube and begins to drop, turn the

Calibration Shut Off Valve (above

flow meter) to

calibrate

position.

WHEN LIQUID LEVEL BEGINS

TO DROP

TURN SHUTOFF VALVE RIGHT

PRESS ENTER

FLO OFF

Press

Turn Left Air Valve to

siphon

position. Arrow pointing down
Fluid passing through siphon to

drain will be observed.

TURN LEFT VALVE DOWN

PRESS ENTER

SIPH

Press

When siphoning stops:
Turn Left Air Valve to

calibrate

position. Arrow pointing up
Open cal port on flow cell cap.
Turn Right Air Valve to

mix

position. Arrow pointing down

WHEN SIPHONING STOPS

TURN LEFT VALVE UP

OPEN CAL PORT
TURN RIGHT VALVE DOWN

PRESS ENTER

Alr

上海肯强贸易有限公司
http://www.kq17.com.cn

Summary of Contents for Orion 2111LL























































































































Search results

Summary of Contents for Orion 2111LL

Reviews:

Related manuals for Orion 2111LL

Brands by name

Popular brands

Thermo Scientific Orion 2111LL, User Manual

Search results

Summary of Contents for Orion 2111LL

Reviews:

Related manuals for Orion 2111LL

Brands by name

Popular brands