manualshive.com logo in svg

Thermo Scientific 42iQTL, Instruction Manual

Share
Download
Thermo Scientific 42iQTL Instruction Manual Download Page 95

Operation 

Settings 

Thermo Scientific 

42iQTL Instruction Manual     

3-69

 

 

The Maintenance History screen allows the user to view when components 
are replaced, rebuilt, or cleaned. When a user changes a part in the change 
part screen, the new row will be automatically created at the top in the 
maintenance history table. 

Use the 

 and 

 buttons to move up and down and the 

 and 

 

buttons to move left and right. 

Home Screen>Settings>Health Check>Maintenance>Maintenance 
History 

Note  

Retrieving maintenance history data, it may take a few seconds... 

▲

  

 

The Maintenance History screen contains the following information: 

●

 

Part:

 Component that has been fixed. 

●

 

Fix:

 The type of maintenance. 

●

 

Date:

 Shows date/time when service was logged. 

●

 

Service Months:

 Amount of time in months since last service. 

●

 

Comments:

 Shows comments entered from time of change. 

 

Maintenance History

Summary of Contents for 42iQTL























































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands