Thermo Scientific 42iQTL Instruction Manual Download Page 93

Page: 93 / 310

Operation

Settings

Thermo Scientific

42iQTL Instruction Manual

3-67

●

Down:

●

Reaction Chamber/Cooler:

Consists of the PMT and PMT base

socket. Each highlights on their own.

●

PMT:

Service interval for PMT.

●

PMT Base Socket:

Service interval for PMT base socket.

●

Converter Cartridge:

Service interval for converter cartridge.

●

Ozonator Assembly:

Service interval for ozonator assembly.

●

Scrubber:

Service interval for NH

scrubber.

●

Sample Permeation Dryer:

Service interval for sample permeation

dryer.

●

Ozone Permeation Dryer:

Service interval for ozone permeation

dryer.

●

Flow System:

Service interval for the flow system components.

●

Pump:

Service interval for pump.

●

Capillary (Sample):

Service interval for capillaries.

●

Capillary (Ozone):

Service interval for capillaries.

●

DC Power Supply:

Service interval for DC power supply.

●

Fan Filter:

Service interval for fan filter.

●

System Components:

Service interval for system components.

●

Purafil:

Service interval for purafil.

●

Charcoal:

Service interval for charcoal.

●

Dri-Rite:

Service interval for dri-rite.

Summary of Contents for 42iQTL























































































































































































































































































































Search results

Summary of Contents for 42iQTL

Reviews:

Brands by name

Popular brands

Thermo Scientific 42iQTL, Instruction Manual

Search results

Summary of Contents for 42iQTL

Reviews:

Brands by name

Popular brands