manualshive.com logo in svg

Thermo Scientific 42iQTL, Instruction Manual

Share
Download
Thermo Scientific 42iQTL Instruction Manual Download Page 116

Operation 

Settings 

3-90

     42iQTL Instruction Manual 

Thermo Scientific 

 

The Communications screen allows the user to set TCP/DHCP 
parameters, Serial settings, Analog I/O and Digital I/O, Email Server, and 
Instrument ID. Buttons are grayed out if not selected in 
Settings>

Configuration

. 

Home Screen>Settings>Communications

 

 

The Communications screen contains the following information: 

●

 

Wired TCP/DHCP: 

Settings for communicating with the instrument 

through wired Ethernet. 

●

 

Serial RS-232/485: 

Settings for communicating with the instrument 

through RS-232/485 protocol. This is only visible if selected in 
Settings>Configuration>Communications Board. 

●

 

Analog I/O: 

Settings for communicating with the instrument through 

analog I/O settings. This is only visible if selected in 
Settings>Configuration>Analog I/O. 

●

 

Digital I/O: 

Settings for communicating with the instrument through 

digital I/O settings. This is only visible if selected in 
Settings>Configuration>Digital I/O. 

●

 

Email Server (SMTP): 

Settings for communication with email. 

●

 

Instrument ID: 

Allows the user to edit the instrument identification 

number (ID). The ID is used to identify the instrument when using 
protocols to control the instrument or collect data. It may be necessary 
to edit the ID number if two or more of instruments of the same model 
are connected to one computer. Valid instrument ID numbers are from 
0 to 127. The 42iQTL has a default instrument ID of 1. 

Communications

Summary of Contents for 42iQTL























































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands