manualshive.com logo in svg

Thermo Scientific 42iQTL, Instruction Manual

Share
Download
Thermo Scientific 42iQTL Instruction Manual Download Page 136

Operation 

Settings 

3-110

     42iQTL Instruction Manual 

Thermo Scientific 

 

The Time Zone screen allows the user to set the time zone for the Network 
Time Protocol (NTP) server. This should be set to the time zone that the 
instrument is located in. 

Use the 

 and 

 buttons to select. 

Home Screen>Settings>Instrument Settings>Clock>Time Zone

 

 

The Time Zone screen contains the following information: 

●

 

Date Line West(UTC-12) 

●

 

Samoa Time Zone(UTC-11) 

●

 

Aleutian Time Zone(UTC-10) 

●

 

Alaskan Time Zone(UTC-9) 

●

 

Pacific Time Zone(UTC-8) 

●

 

Pacific Daylight Savings(UTC-7) 

●

 

Mountain Time Zone(UTC-7) 

●

 

Mountain Daylight Savings(UTC-6) 

●

 

Central Time Zone(UTC-6) 

●

 

Central Daylight Savings((UTC-5) 

●

 

Eastern Time Zone(UTC-5) 

●

 

Eastern Daylight Savings(UTC-4) 

●

 

Atlantic Time Zone(UTC-4) 

●

 

Mid-Atlantic(UTC-3) 

●

 

South Georgia(UTC-2) 

●

 

Cape Verde Time(UTC-1) 

Time Zone

Summary of Contents for 42iQTL























































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands